Libra i.MX 8M Plus FPSC Manuals

HEAD

Table of Contents

• 1. PHYTEC Documentation
  • 1.1. Supported Hardware
• 2. Getting Started
  • 2.1. Get the Image
  • 2.2. Write the Image to SD Card
  • 2.3. First Start-up
• 3. Building the BSP
  • 3.1. Basic Set-Up
  • 3.2. Get the BSP
• 4. Installing the OS
  • 4.1. Bootmode Switch (S1)
  • 4.2. Flash e.MMC
• 5. Development
  • 5.1. Standalone Build preparation
  • 5.2. U-Boot standalone build
  • 5.3. Kernel standalone build
  • 5.4. Working with UUU
  • 5.5. Host Network Preparation
  • 5.6. Booting the Kernel from a Network
  • 5.7. Accessing the Development states
  • 5.8. Accessing the Latest Upstream Support
  • 5.9. Format SD card
• 6. Device Tree (DT)
  • 6.1. Introduction
  • 6.2. PHYTEC i.MX 8M Plus BSP Device Tree Concept
• 7. Accessing Peripherals
  • 7.1. i.MX 8M Plus Pin Muxing
  • 7.2. RS232
  • 7.3. Network
  • 7.4. SD card
  • 7.5. e.MMC Devices
  • 7.6. SPI Master
  • 7.7. GPIOs
  • 7.8. LEDs
  • 7.9. I²C Bus
  • 7.10. EEPROM
  • 7.11. RTC
  • 7.12. USB Host Controller
  • 7.13. CAN FD
  • 7.14. PCIe
  • 7.15. Video
  • 7.16. Display
  • 7.17. Power Management
  • 7.18. Watchdog
  • 7.19. snvs Power Key
  • 7.20. ISP
  • 7.21. On-Chip OTP Controller (OCOTP_CTRL) - eFuses

BSP-Yocto-NXP-i.MX8MP-FPSC-ALPHA1

Table of Contents

• 1. PHYTEC Documentation
  • 1.1. Supported Hardware
• 2. Getting Started
  • 2.1. Get the Image
  • 2.2. Write the Image to SD Card
  • 2.3. First Start-up
• 3. Building the BSP
  • 3.1. Basic Set-Up
  • 3.2. Get the BSP
• 4. Installing the OS
  • 4.1. Bootmode Switch (S1)
  • 4.2. Flash e.MMC
• 5. Development
  • 5.1. Standalone Build preparation
  • 5.2. U-Boot standalone build
  • 5.3. Kernel standalone build
  • 5.4. Working with UUU
  • 5.5. Host Network Preparation
  • 5.6. Booting the Kernel from a Network
  • 5.7. Accessing the Development states
  • 5.8. Accessing the Latest Upstream Support
  • 5.9. Format SD card
• 6. Device Tree (DT)
  • 6.1. Introduction
  • 6.2. PHYTEC i.MX 8M Plus BSP Device Tree Concept
• 7. Accessing Peripherals
  • 7.1. i.MX 8M Plus Pin Muxing
  • 7.2. RS232
  • 7.3. Network
  • 7.4. SD card
  • 7.5. e.MMC Devices
  • 7.6. SPI Master
  • 7.7. GPIOs
  • 7.8. LEDs
  • 7.9. I²C Bus
  • 7.10. EEPROM
  • 7.11. RTC
  • 7.12. USB Host Controller
  • 7.13. CAN FD
  • 7.14. PCIe
  • 7.15. Video
  • 7.16. Display
  • 7.17. Power Management
  • 7.18. Watchdog
  • 7.19. snvs Power Key
  • 7.20. ISP
  • 7.21. On-Chip OTP Controller (OCOTP_CTRL) - eFuses

Quickstart Guide ALPHA1

Table of Contents

• 1. Introduction
• 2. Requirements
  • 2.1. Included in the Kit
  • 2.2. Components
  • 2.3. Additional (optional) equipment (not included in Alpha Kit)
  • 2.4. Linux Host PC
• 3. Connecting the Board
  • 3.1. Connecting the DEBUG USB interface
  • 3.2. Powering the Board
• 4. Prebuilt Images
• 5. System Booting
  • 5.1. Boot with SD-Card