i.MX 95 Manuals

HEAD

Table of Contents

• 1. PHYTEC Documentation
  • 1.1. Supported Hardware
• 2. Getting Started
  • 2.1. Get the Image
  • 2.2. Write the Image to SD Card
  • 2.3. First Start-up
• 3. Building the BSP
  • 3.1. Basic Set-Up
  • 3.2. Get the BSP
• 4. Installing the OS
  • 4.1. Bootmode Switch (S1)
  • 4.2. Flash e.MMC
• 5. Development
  • 5.1. Standalone Build preparation
  • 5.2. U-Boot standalone build
  • 5.3. Kernel standalone build
  • 5.4. Working with UUU
  • 5.5. Host Network Preparation
  • 5.6. Booting the Kernel from a Network
  • 5.7. U-Boot PXE Boot
  • 5.8. Accessing the Development states
  • 5.9. Format SD card
  • 5.10. Ampliphy-boot
  • 5.11. Working with FIT images
• 6. Device Tree (DT)
  • 6.1. Introduction
  • 6.2. PHYTEC i.MX 95 BSP Device Tree Concept
• 7. Accessing Peripherals
  • 7.1. i.MX 95 Pin Muxing
  • 7.2. Ethernet
  • 7.3. SD card
  • 7.4. e.MMC Devices
  • 7.5. GPIOs
  • 7.6. I²C Bus
  • 7.7. EEPROM
  • 7.8. RTC
  • 7.9. USB Host Controller
  • 7.10. Video
  • 7.11. Display
  • 7.12. Power Management
  • 7.13. Thermal Management
  • 7.14. PWM fan
  • 7.15. TPM
  • 7.16. GPU
  • 7.17. Watchdog
• 8. NXP GoPoint demo suite
  • 8.1. ML Benchmark

Quickstart Guide ALPHA1

Table of Contents

• 1. Introduction
• 2. Requirements
  • 2.1. Included in the Kit
  • 2.2. Components
  • 2.3. Additional (optional) equipment (not included in Alpha Kit)
  • 2.4. Linux Host PC
• 3. Connecting the Board
  • 3.1. Connecting the DEBUG USB interface
  • 3.2. Powering the Board
• 4. Prebuilt Images
• 5. System Booting
  • 5.1. Boot with SD-Card

BSP-Yocto-NXP-i.MX95-ALPHA1

Table of Contents

• 1. PHYTEC Documentation
  • 1.1. Supported Hardware
• 2. Getting Started
  • 2.1. Get the Image
  • 2.2. Write the Image to SD Card
  • 2.3. First Start-up
• 3. Building the BSP
  • 3.1. Basic Set-Up
  • 3.2. Get the BSP
• 4. Installing the OS
  • 4.1. Bootmode Switch (S1)
  • 4.2. Flash e.MMC
• 5. Development
  • 5.1. Standalone Build preparation
  • 5.2. U-Boot standalone build
  • 5.3. Kernel standalone build
  • 5.4. Working with UUU
  • 5.5. Host Network Preparation
  • 5.6. Booting the Kernel from a Network
  • 5.7. Accessing the Development states
  • 5.8. Format SD card
• 6. Device Tree (DT)
  • 6.1. Introduction
  • 6.2. PHYTEC i.MX 95 BSP Device Tree Concept
• 7. Accessing Peripherals
  • 7.1. i.MX 95 Pin Muxing
  • 7.2. Ethernet
  • 7.3. SD card
  • 7.4. e.MMC Devices
  • 7.5. GPIOs
  • 7.6. I²C Bus
  • 7.7. EEPROM
  • 7.8. RTC
  • 7.9. USB Host Controller
  • 7.10. Video
  • 7.11. Display
  • 7.12. Power Management
  • 7.13. Thermal Management
  • 7.14. GPU
  • 7.15. Watchdog
• 8. NXP GoPoint demo suite
  • 8.1. ML Benchmark